View current state and status of a Monitored Asset – Primex Support

The state of a Monitored Asset is determined by the last transmitted reading and operating condition of its assigned sensor(s). Its status identifies the condition that resulted in the asset either entering a Warning or Alarm state.

You can view the state of a Monitored Asset from your Dashboard or from the profile of the Monitored Asset. The Dashboard displays a summary of the state of all Monitored Assets in both a circle and list view.

A Monitored Asset may have more than one monitoring point, which results in its state being calculated by OneVue. A calculated state is based on the most severe condition of the sensors assigned to the Monitored Asset. When a Monitored Asset has multiple assigned sensors and one sensor is in an Alarm state, the Monitored Asset is also in an Alarm state, regardless if any additional assigned sensors are in a Normal state.

For example, a room may require both its ambient air temperature and relative humidity level to be logged and monitored. The Monitored Asset will have two sensor types - one temperature and one humidity. This room could even expand its monitoring to include a differential pressure sensor, resulting in three monitoring points.

View the state and status of a Monitored Asset

Go to Monitoring > Monitored Assets.
Locate the Monitored Asset. The state and status column is displayed.
To view its state history, from the list select the Name link of the Monitored Asset > its profile is displayed > select State History.

Monitored Asset state and status

State	Current Condition	Status resulting in State
Normal	The last transmitted sensor reading is within the expected, normal range of the Monitored Asset and the sensor device is operating as expected.	Its status will be blank during this state. Differential Pressure Monitoring only - an Open status indicates the Differential Pressure Door Switch is in an Open status. When in an Open status for longer than the time period set in its Door Delay Alarm setting, the Monitored Asset is set to an Alarms Disabled state.
Warning	Temperature, Temperature and Humidity, and Differential Pressure monitoring (sensors). The last transmitted reading is either below or above its Normal Condition (range) of the Monitored Asset, but the amount of time the reading has been out of range has not exceeded the time period set in its Alarm Delay setting. When a Monitored Asset is in a Warning state, OneVue does not activate an alert continues to log, store, and monitor the sensor readings and sensor device operating conditions	Out of Range
Alarm	A condition requires immediate attention. The condition resulting in the Alarm state is indicated by its Status. When set to an Alarm state, OneVue: activates an alert for the alerting condition resulting in the Alarm state; alerts require that the Monitored Asset is assigned to an alert rule. continues to log, store, and monitor the sensor readings and sensor device operating conditions	Enters an Alarm state due to any of the statuses below: Out of Range, Past Alarm Delay The last reading was either below or above its Normal Condition (temperature, temperature and humidity, or differential pressure sensor) or the last condition is not its Normal Condition (water leak and contact closure sensor). The amount of time the last reading/condition has been out of range (not within its Normal Condition), has exceeded the time period set in its Alarm Delay. If the Alarm Delay setting is set to 0 (zero), the Monitored Asset is immediately set to an Alarm state with the status of Out of Range, Past Alarm Delay. Unresponsive Indicates the sensor device has not checked-in to OneVue for more than the time period set in the sensor's gateway Unresponsive Timeout setting. Commonly, an Unresponsive status is due to a network connectivity issue has prevented the Primex device from checking-in to your OneVue account or the device has no power. No Probe Indicates a probe has either been removed from the temperature sensor or the probe is malfunctioning. When a probe is removed from a temperature sensor device, a no probe status is automatically sent to OneVue. Low Battery Indicates the sensor device has reported a low battery level. It's recommend to replace the device batteries to avoid a loss of data. All data stored in non-volatile memory is lost when a device loses all power.
Suspended	A OneVue user sets a Monitored Asset to the Suspended state. This state is designed for use during a temporary condition, such as when a Monitored Asset is being repaired or replaced. The Monitored Asset is required to be set to a Normal state by a system user to resume alerting. When set to a Suspended state, OneVue: acknowledges and ends any active alerts does not generate alerts does not monitor its readings or sensor device operating conditions continues to log and store readings and sensor device operating conditions - continues to show status changes only	Displays status changes only - not monitored during this state.
Decommissioned	A OneVue user sets a Monitored Asset to the Decommissioned state. The Decommissioned state is designed to permanently disable a Monitored Asset from your account, such as when an asset has been taken out of service. When set to Decommissioned state, the system: detaches the Monitored Asset from its assigned sensor(s) acknowledges and ends any active alerts retains all historical reading data that was stored in the system prior to the Monitored Asset being set to a Decommissioned state allows the Monitored Asset to be permanently deleted from your OneVue account.
Unmonitored	A sensor is not assigned to the Monitored Asset. Therefore, no reading or sensor device operating data is associated to the Monitored Asset. This state is set by OneVue and cannot be set by a user. When in an Unmonitored state, the system: does not monitor the Monitored Asset or generate alerts
Alarms Disabled - Differential Pressure Monitoring only	The Alarms Disabled only applies when Door Monitoring is configured at the Differential Pressure sensor device. The Monitored Asset is set to the Alarms Disabled state when the Door Switch has been in an Open status for longer than the time period set within its Door Delay setting. When a Monitored Asset is set to the Alarms Disabled state, the system: acknowledges and ends any active alerts continues to only log and store readings, device operating conditions, and statuses does not generate alerts	Past Door Delay -

Articles in this section

View the state and status of a Monitored Asset

Monitored Asset state and status

Related articles